物品名称 规格型号 数量 单位 描述
| 全启安全阀 | DA22F-40P | 2.00 | 个 | {"规格型号":"DA22F-40P","公称压力":"4MPa","公称通径":"25mm","压力等级":"0.7-1.0MPa","整定压力":"0.84MPa","排放压力":"0.92MPa","回座压力":"0.63MPa","序列号":"无","流道直径":"25mm","连接方式":"螺纹连接","适用温度":"-196~60℃","输送介质":"氩气、氮气","主体材质":"304不锈钢","国产/进口":"国产","生产厂家":"****点击查看门厂家","特殊要求":"喉部通径16mm 开启高度≥4mm","使用寿命":"730天","参照标准":"GB/T 12241-2005"} |
| 弹簧式安全阀 | A27W-10T/DN20 | 2.00 | 个 | {"规格型号":"A27W-10T/DN20","公称压力":"1Mpa","公称通径":"20mm","整定压力":"0.85MPa0.85MPa","适用温度":"200℃200℃"} |
| 精密调压阀 | 11-818—100 | 5.00 | 个 | {"规格型号":"11-818—100","阀体材质":"锌合金","阀芯材质":"合成橡胶","接口尺寸":"G1/4","特殊需求":"外形颜色：黑色；弹簧的压力范围：0.07-4bar；工作介质：压缩空气；溢流/非溢流：溢流；最大进气压力：10bar；使用寿命365天以上。","参照标准":"GB/T 4213-2008"} |
| 支承辊油气分配器 | K30/0265A0109 | 2.00 | 套 | {"规格型号":"K30/0265A0109","整体尺寸":"外径25.2mm","整体材质":"H59","进出口接头尺寸(螺纹)":"G3/8","压盖尺寸(螺纹)":"M30*1.5","固定方式":"螺纹压盖压紧","工作温度":"0~120℃","流量范围":"54cm3/h","使用寿命":"36月","特殊要求":"进口/REBS"} |
| 油气接头 | DN6/10/925/1552 | 4.00 | 个 | {"规格型号":"DN6/10/925/1552","工作压力":"0.8MPa","连接方式":"外螺纹M24*1.5","材质":"表面氧化钢","密封件材质":"FKM","适用介质":"齿轮油、气混合","特殊要求":"通径6mm","使用寿命":"36月"} |
| 油气快换接头公端 | G3/8A/LP-007-2-WR017-13-2 | 4.00 | 个 | {"规格型号":"G3/8A/LP-007-2-WR017-13-2","工作压力":"0.8Mpa","连接方式":"外螺纹G3/8 A","材质":"化学镀镍钢","密封件材质":"FKM","适用介质":"齿轮油、气混合","特殊要求":"通径7mm","使用寿命":"730天","参照标准":"GB/T 22076-2008","备注":"到货质量不符，退换货处理"} |
| 气动比例阀 | VP5006BJ111H00 | 10.00 | 个 | 型号 VP5006BJ111H00 阀门类型 气动控制阀 接口规格 G1/4 额定电压及功率 24V 工作压力 0-1Mpa 阀体材质 铝合金 手动复位 是 计量单位 ITE |
| 电磁阀 | 2W-500-50 | 2.00 | 个 | {"规格型号":"2W-500-50","公称压力":"0-1MPa","公称通径":"50mm","连接方式":"内螺纹连接；螺纹规格R2","驱动方式":"电动","适用电压":"DC24V","气源压力/液体压力":"0-0.6MPa","反馈信号":"无","是否配带执行机构":"无","执行机构型号":"无","执行机构与阀门连接尺寸":"无","工作温度":"-5-80℃","输送介质":"气体","主体材质":"黄铜","国产/进口":"国产","特殊要求":"无","使用寿命":"≥180天","参照标准":"JB/T 7352-2010","备注":"如产品不符合技术要求，退换货处理，产生的一切费用由供货方承担。"} |
| 块型单项节流阀 | G1/2*65*30 | 4.00 | 件 | {"规格型号":"G1/2*65*30","公称压力":"0.1~1MPa","公称通径":"G1/2mm","连接方式":"螺纹连接","驱动方式":"手动控制","最大流量":"7.5I/min","常用流量":"0.5~2 I/min","适用电压":"无","反馈信号":"无","是否配带执行机构":"无","执行机构型号":"无","执行机构与阀门连接尺寸":"无","工作温度":"-5~60℃","输送介质":"压缩空气","主体材质":"铝合金","国产/进口":"国产进口均可;无品牌要求.","特殊要求":"单向节流；密封:丁晴橡胶","使用寿命":"1095天","参照标准":"GB/T 4213-2008","备注":"可推行备件国产化,需认真核实与原件材质及规格尺寸.(原件品牌为NORGEN ;T1000C4800请参考其制作工艺,),到货备件满足尺寸和使用要求均可.验收标准:到货需出具合格证或产地证明;包装完好无损备件无腐蚀;无破损;安装尺寸正确无误,不合格品处理标准:如出现质量和安装尺寸问题;厂家及时给予退换货;由此产生的费用由供货商自行承担."} |
| 叠片过滤器过滤单元 | 4寸 | 9.00 | 套 | {"型号":"4寸","图号":"无","材质":"叠片材质：PP型工程塑料；中柱材质要求：增强尼龙；外壳材质要求：增强尼龙","所属设备名称":"叠片过滤器","设备型号":"PLN4-9","设备生产厂家":"不指定","国产/进口":"国产","使用寿命":"730天","特殊要求":"无","参照标准":"JB/T 13510-2018","备注":"一、技术参数：叠片：1、内径：100mm,2、外径：130mm, 3、宽度：15mm,4、过滤精度：200μm,5、叠片材质：PP型工程塑料;中柱：1、高度：480mm，2、材质要求：增强尼龙；外壳：1、内壁直径：180mm，2、壁厚：5mm，3、高度：505mm，4、材质要求：增强尼龙;四通：1、高度：210mm，2、长度：340mm，3、进出口口径DN100、拷贝林接口；4、材质要求：增强尼龙。二、要求：1套过滤单元包含上下两个过滤筒H型，配套扣环2个、接头2个、四通1个，配套相应密封胶圈，1套过滤单元通量：52-70m3/h；单位：套；进口、国产信息：国产；使用环境：≤95℃；工作压力：0.2-1.0MPa；使用寿命：≥24个月；三、验收标准：到货叠片为组装装满状态，随货附带产品合格证，使用说明书，材质报告，与技术要求不符时厂家无条件给予退换货处理。"} |
| 换向阀 | 4WE-6-J62/EG24N9K4/B10 | 2.00 | 个 | {"规格型号":"4WE-6-J62/EG24N9K4/B10","材质":"铸铁","密封件材质":"丁腈橡胶","使用寿命":"1095天"} |
| 前置过滤器 | FG4040WT | 1.00 | 个 | {"规格型号":"FG4040WT","公称直径":"DN40mm","公称压力":"0.4Mpa","连接方式":"螺纹连接","过滤精度":"50μm","材质":"铝合金","特殊要求":"两端带DN40尺寸不锈钢对丝,替换滤芯1个,替换端盖密封条1条.","使用寿命":"720天","参照标准":"GB/T 36051-2018","备注":"该装置用于天然气过滤,到货带合格证.到货开箱测量尺寸与要求尺寸相符,过滤器表面无明显划伤及破损、开裂现象,盖板密封良好无泄漏.验收若与技术要求不符,供货商需无条件进行退换货处理,期间产生的费用由供货商负责."} |
| 燃气稳压阀 | 1803B2 | 1.00 | 个 | {"型号":"1803B2","规格":"1-1/4\"","材质":"铸铁","品牌":"无指定品牌厂家","使用介质":"天然气","进口压力范围":"≤0.862MPa","出口压力范围":"0.87 kPa - 13.8 kPa","执行标准":"BSEN 16129:2013","备注":"到货附带使用说明书及合格证.使用寿命需≥720天,到货开箱测量接口尺寸等,若测量不合格供货商需无条件进行退换货处理,期间产生的费用由供货商负责."} |
| 燃气放散阀 | ms25 | 1.00 | 台 | {"型号":"ms25","规格":"DN25","材质":"铸铁","品牌":"任意品牌及厂家","使用介质":"天然气","进口压力范围":"6bar","出口压力范围":"80~600mbar","执行标准":"CJ/T 335-2010","备注":"到货附带使用说明书及合格证.使用寿命需≥720天.到货测量接口等尺寸,若产品不合格,供货商无条件进行退换货处理,期间产生的费用由供货商负责."} |
| 常开阀 | SV08-2NOSP-DC24V | 2.00 | 个 | {"规格型号":"SV08-2NOSP-DC24V","图号":"无","材质":"碳钢","密封件材质":"丁腈橡胶","电压":"DC24V","所属设备名称":"静电涂油机","设备型号":"E890","设备生产厂家":"任意品牌及厂家","国产/进口":"国产","使用寿命":"365天","特殊要求":"带电磁阀线圈,接口尺寸：3/4”-16 UNF","参照标准":"GB/T 8100.3-2021","备注":"接口尺寸：3/4”-16 UNF 到货后包装完好无损，带有合格证。如果所送物品与技术参数不相符，必须给予退、换货，产生一切费用由供货商全部承担。"} |
| 常闭阀 | SV08-20/NCP-DC24V | 2.00 | 个 | {"规格型号":"SV08-20/NCP-DC24V","图号":"无","材质":"碳钢","密封件材质":"丁腈橡胶","电压":"DC24V","所属设备名称":"静电涂油机","设备型号":"E890","设备生产厂家":"达涅利","国产/进口":"国产","使用寿命":"365天","特殊要求":"带电磁阀线圈","参照标准":"GB/T 8100.3-2021","备注":"到货后包装完好无损，带有合格证。如果所送物品与技术参数不相符，必须给予退、换货，产生一切费用由供货商全部承担。"} |
| 喷淋阀膜片 | Φ36*3.5 | 62.00 | 个 | {"规格型号":"Φ36*3.5","内径":"Φ无mm","外径":"Φ36mm","长度":"无mm","材质":"氟橡胶","特殊要求":"硬度：75±5 shore A ;耐油耐腐蚀；工作温度10-80℃；使用寿命365T天","参照标准":"GB/T 30308-2013","备注":"喷淋阀膜片：外径36mm；厚度3.5mm；硬度要求75±5 shore A ;耐油耐腐蚀；工作温度10-80℃；使用寿命365天\n到货验收：到货后应完好无损，表面光洁无杂质，需附带出厂材质证明、检验报告及产品合格证，如果到货产品与技术要求不符或存在缺陷，供货商无条件更换或退货。退换货产生的一切费用由供货商承担。"} |
| 手动换向阀 | 4HV430-15 | 4.00 | 个 | {"规格型号":"4HV430-15","公称压力":"0.6MPa","公称通径":"15mm","连接方式":"1/2管螺纹连接","出口压力范围":"0-0.6MPa","驱动方式":"手动","适用电压":"无","反馈信号":"无","是否配带执行机构":"无","执行机构型号":"无","执行机构与阀门连接尺寸":"无","工作温度":"20-40℃","输送介质":"压缩空气","主体材质":"铝合金","国产/进口":"国产","特殊要求":"无","使用寿命":"365天","参照标准":"JB/T 6378-2008","备注":"到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 阀板 | 1130×860mm | 2.00 | 套 | {"参照标准":"JB/T 5000","规格型号":"1130×860mm","材质":"不锈钢310S","使用寿命":"不低于6个月月","验收标准":"到货后现场实测阀板成分，所有配件均需完全满足310S材质要求，阀板表面处理需提供盖章版检测报告。不满足上述要求及使用过程中出现质量问题时厂家应及时给予退换货。","备注":"供货范围包括阀板、连接轴及其配件，阀板及所有配件材质均为310S不锈钢；焊接执行JB/T 5000.3-1998通用技术条件，接头及坡口形式尺寸执行GB/T 985-88与GB/T 986-88通用技术条件；阀板与轴之间采用螺栓连接后，再连续角焊缝，焊缝高度为8-10 mm，采用310S不锈钢焊条，保证焊后阀板平整，无明显扭曲变形；所有型钢与钢板切割边要求光洁度RZ200；表面处理：阀板表面喷涂陶瓷氧化锆，表面硬度：800-1200HV，结合强度＞45MPa，孔隙率＜3%，喷涂厚度300μm，耐温1600℃。"} |
联系人8个
可引荐人脉580人
历史招中标信息134条
相似项目推荐